So dumb they made them national heroes to a vast section of the country and failed to keep them out of the state house as well and after the election there may be more dems in the state house as well
I just put up an awning over our back deck. Now it’s time for modifications. I’m going to adjust how the straps connect for the fabric so it’s tighter and water runs off better. then I’m going to seam seal and put on some waterproofing spray.
After that, my daughter and I are building a padded bench for a window nook in her room. The design and measurements are done. Fabric and foam have been purchased. Actual work completed: zero.
Just got a bunch of stuff delivered to build my own hyperhdr tv backlight. Its a relatively small project, but im hoping itll have a huge impact on my viewing experience 😊
Ooo is there a guide you are following for this? I tried setting this up a few years back during covid and never could get it working right. I still think it was faulty hardware but I went through at least a half-dozen grabbers.
Yeah, there is a guide for the raspberry raspberrypi.com/…/raspberry-pi-tv-ambient-lightin…I donk know if hyperhdr would run on weaker, more readily available hardware than the pi 3. ive seen some YouTuber (dont remember who) use Hyperion with a Pico, but here was noticable delay. Since hyperhdr is a more optimised fork of hyperion intended for 4k content, the pico may be able to to run hyperhdr for 1080p content, but im not willing to take that risk. Also check what kind of power supplies you can even get. 5v 15a power supplies apparently don’t exist in Germany, so i had to use 30 led/meter strips instead of 60
Awesome, thanks! I may dive back into this project again since I would still really like to do it. I think I actually have a spare Pi 4 around here somewhere that I got for my 3d printers but ended up swapping that to a thin client. Appreciate it!
Thank you! The surfacing part was actually done mostly by hand because if a chicken and egg situation of making the inside components and adding the hinge, without throwing things off balance on the lathe. But after four prototypes, I definitely learned a lot!
We celebrated our 8th wedding anniversary yesterday, easy peasy 👍 The trick is simple, don’t marry someone who is an asshole. I certainly didn’t, and hope my wife feels the same way 😅
Trying to repair a spice grinder. After swearing a bunch and cutting up my fingers I gave up putting the original switch and safety lock and decided to cannibalize a new switch from a space heater that isn’t a POS.
Making progress on linen shorts. The belt fits, despite some unfortunate inaccuracies while attaching the waistband. Button hole and button are next. Or hemming…
Planning to replace the old TV coax cable with Ethernet cable so everybody in the house gets their own low-latency connection for gaming. The problem is that TV cable is installed in a daisy chain while Ethernet has a star topology, and there’s only room for one cable from the basement to upstairs. So at the moment I’m pondering whether to keep the daisy chain and place a switch in every room, use some sort of MoCA (Ethernet over coax) adapter or go all the way and install fiber.
Also, we should really replace the carpet in the master bedroom with hardwood soon.
I’ll go ahead and say that I’m using a MoCA connection to my main PC, and have no complaints about it at all. It’s the 2.5Gbps by ScreenBeam.
Not sure how exactly that works with the daisy chain, but brief reading seems to indicate that it should be fine to add a MoCA endpoint in each room, unless you wanna just rewire the upstairs with a single switch and Ethernet cables to each room up there, assuming you have room to run all the cables in the upstairs only.
I have my guest bath torn down to studs. A new cast iron tub went in. I had to replace a few termite-eaten studs from who knows when. The house is 60 years old. I’m working on putting it all back together now. New insulation, then drywall and backer board. Then, moving on to the shower tile. Also, I have to schedule a new stone top for the vanity and get a new sink and faucet. Then, texture and paint all the walls and finally replace all the floor tile in the area. I started a week ago, but it’s all moving quickly. If I can keep up the momentum, maybe I will be finished in a month.
beehaw.org
Oldest