The most requested Vertical Tabs will make an appearance in the upcoming Firefox. The feature can now be turned on in Nightly itself without the need to rely on third-party extensions or separate Nightly builds.
The 42-year-old son of U.S. Sen. Kevin Cramer crashed into a North Dakota sheriff's vehicle during a police chase, pushing it into a deputy and killing him, according to authorities and the ...
Speaking from personal experience, it’s often very difficult to get someone into treatment unless they’re either so far gone (unresponsive, or immediately obvious they’re not living in reality) that a doctor will sign off on it, or someone gets hurt and the justice system can act instead
The “immediately obvious they’re not living in reality” criteria is much dumber than you think. Someone can be delusional but because they can agree on basic facts, they’ll be released.
Also if the pfsense router is where the WAN IP lives as might be the case in simpler setups where it is the wan router, it would just note that “hey thats me” and resolve unless there were specific rules preventing that traffic.
Dc-Dc is pretty efficient, I wouldn’t worry about conversion after the initial 48v, but I would potentially worry about losses in poor quality home wiring on longer runs in bigger homes
The 10GBase-LR is 1310nm and the QSFP-40G-LR4 CWDM channels are 1271, 1291, 1311 and 1331 nm. Are the 1310nm and 3rd channel 1311nm technically compatible?...
Unless specifically stated, generally fiber transceivers only run at the stated rate and would expect every channel to negotiate unless it had a 4x10 mode supported by both the transceiver and the device you put it in (which is what that DAC splitter is for), though once you split the lanes this way, a single pair would only ever run at 10g
Additionally the nature of CWDM on a single pair means the 10g side will see all four signals simultaneously as there are no filters on that side of the connection. QSFP+ runs like this because it’s cheaper to manufacture and a single transmit/receive pair is only necessary in much longer range transport which typically uses more specialized expensive hardware for better long range signal integrity.
In short: no, this won’t work and transceivers generally only ever run in one mode et once as configure by the switch/router they’re inserted in, and the modes you’re asking a qsfp+ to run in are mutually exclusive based on type (single lc pair cwdm at 40g vs 4x10g MPO/MTP with changeable modes). Fiber doesn’t have the same “negotiation” features that copper Ethernet does.
Number of users total isn’t a big deal, number of concurrent users is. If nobody’s accessing them often it’s not particularly hard on your hardware either
Vertical Tabs can now be enabled in Firefox Nightly and are movable to the right side ( windowsreport.com )
The most requested Vertical Tabs will make an appearance in the upcoming Firefox. The feature can now be turned on in Nightly itself without the need to rely on third-party extensions or separate Nightly builds.
Son of US Sen. Kevin Cramer crashes during police chase, killing North Dakota sheriff's deputy ( www.dailykos.com )
The 42-year-old son of U.S. Sen. Kevin Cramer crashed into a North Dakota sheriff's vehicle during a police chase, pushing it into a deputy and killing him, according to authorities and the ...
Pfsense accessible internally via WAN IP
So, I just realized that if i use my WAN IP in my browser from within my network, it brings me to my pfsense login page…...
Home-Server Upgrade Recommendations
Hi, could you help me and recommend a good upgrade for my (dated) home server?...
Q: Is PoE energy efficient inside your home?
Is PoE more efficient than plugging in adapters for each network device?...
Can I attach a 10GBase-LR to QSFP-40G-LR4 (CWDM)?
The 10GBase-LR is 1310nm and the QSFP-40G-LR4 CWDM channels are 1271, 1291, 1311 and 1331 nm. Are the 1310nm and 3rd channel 1311nm technically compatible?...
A private libertarian city in Honduras ( www.youtube.com )
How to handle 4TB of photos/videos
Hello,...