#1 - What direction are the floor joists running, you would typically run perpendicular to the joists to minimize waviness on the floor.
#2 - You would typically run it longways past the door, so the sun shining in doesn't go along the board length.
#3 - There's really no WRONG way to do this, because the LVP flooring doesn't have much structure to it, and it'll just follow the contouring of the subfloor. So whatever way you think looks best, go for it.
#4 - If the walls are really out of square, you can also go at a 45 degree angle to hide that. It'll use up a LOT more flooring, but it also looks pretty cool when it's all done.
edit: Picture #2 would be the more "right" way to do it, but again, if that's not what you like, then it's up to you. Also, not sure if this was just the way you are demonstrating, but you're also going to want to have a little more randomness in the board ends, don't have them alternate in a pattern like you have it.
My birthday was last week (May 17). Decided to get my first tattoo, which I wanted to be Trek related. As a kid my family had a VHS tape with a recording of “All Good Things…” (and for unknown reasons, “Caretaker”). So I have seen the episode a dozen times. It is my favorite episode of the franchise. The image I’m...
Here too. Every other outlet in my house was wired backwards, and about a quarter of my outlets had a ground running to the box, but cut short and not connected to anything. I had to splice in so many grounds (really not the best solution, but the alternative was putting in a whole new run)
There's tons of great ones out there, but the ones who really take the time to do it right are usually self-employed. That means they're hard to find unless you know someone who used them before, and can squeeze into their overbooked schedule.
Most of the ones who work for companies have to work faster and cheaper in order to move on to the next project.
It's just tricky to build up a network of folks that really know what they are doing, and can fit you in when you just need a small project.
I am currently redesigning my kitchen in a 1930’s Midwestern USA house. The kitchen has a decent floor area but the floor plan is oddly restrictive....
If it was me, I’d go with a cabinet install that allows for a 24" dishwasher. That’s the standard size, and you might have trouble replacing a broken 18" dishwasher in the future.
Maybe get some drawers to keep the clothes in. Just a couple hangers for jackets or whatnot, but the rest of the clothes would be better folded and put away.
The wires could be managed a little, use some 3m command adhesives with some clips so the wires aren’t getting stepped on or tripped over. The command adhesive comes off really clean, so you won’t wreck the paint. Run the wires along corners of the room and/or behind the desk so you don’t notice them.
If you want to get all bougie, you can get your bed up off the floor, but really, it’s not that big of a deal.
In the two years I've been writing about Americans' changing relationship to work, there's one theme that's come up over and over again: loyalty. Whether my stories are about quiet quitting, or job-hopping, or leveraging a job offer from a competitor to force your boss to give you a raise, readers seem to divide into two groups....
Those disgruntled people in this thread. I suggest you read the article. The first thing it talks about is how companies started outsourcing and treating employees as replaceable, and employees were slow to respond at first, so companies just kept pushing until they finally fucked around enough to find out that they caused this mess.
It’s a pretty good article, and argues that the employers need to step up and start showing real leadership, instead of chasing the lowest contract, and single quarter vision.
How would you lay the floor in this case?
Id do it like this but two people told me other way... Not sure?
In the deep, far future, at the time of the "heat death" of the universe, if I turn on a radio will I get the sound of static or of total silence?
Got a “All Good Things…” tattoo for my birthday. ( startrek.website )
My birthday was last week (May 17). Decided to get my first tattoo, which I wanted to be Trek related. As a kid my family had a VHS tape with a recording of “All Good Things…” (and for unknown reasons, “Caretaker”). So I have seen the episode a dozen times. It is my favorite episode of the franchise. The image I’m...
When you do it yourself and it looks like you did it yourself lol ( lemmy.world )
Okay, my first ever drywall and I know what I did wrong. I just didn't think that small indifference would make it look obviously bad....
What an impressive collection ( lemmy.world )
Aubrey Plaza says what all the interns want to say #aubreyplaza #memes #intern #internships - YouTube ( youtube.com )
Talk me out of an 18" dishwasher. (or into it)
I am currently redesigning my kitchen in a 1930’s Midwestern USA house. The kitchen has a decent floor area but the floor plan is oddly restrictive....
Filming On The ‘Star Trek: Section 31’ Streaming Movie Has Wrapped ( trekmovie.com )
Ultimate Chronological Star Trek Viewing Guide ( www.startrekviewingguide.com )
This was created by Reddit user /u/JohnKFisher, and I think it’s a neat uncluttered guide for all Star Trek that’s especially useful for newbies.
If you are looking for a new obsession ( youtu.be )
cross-posted from: beehaw.org/post/12265699...
Why don't ships onboard sensors detect medical emergencies
It’s something that has bothered me since I realised...
[Thread, post or comment was deleted by the author]
Can I hang kitchen cabinet on my subconstruction I built? ( lemmy.world )
Hey!...
The end of workplace loyalty: Why work feels so broken right now — and how it can be repaired ( www.businessinsider.com )
In the two years I've been writing about Americans' changing relationship to work, there's one theme that's come up over and over again: loyalty. Whether my stories are about quiet quitting, or job-hopping, or leveraging a job offer from a competitor to force your boss to give you a raise, readers seem to divide into two groups....